LU72M series blades are the best choice for production sizing of hard or soft wood up to 3-1/2 inches thick with a miter box. These general purpose blades feature legendary Freud quality and are designed for extra long life in industrial applications. Las
Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Recommended for: thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods. Eliminates need for a small scoring saw blade on table saw work. The 40° points slice through thin bottom layers with no tears or chips. Reduced yearly sharpening costs - less machine downtime.
Freud's bushings are manufactured to the highest precision to insure a cut equal to that of the cutter without the bushing.
Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and re-straightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind its' blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Forrest Woodworker 1 Saw Blade For Radial and Table Saws. These trim and cross-cut ALL PURPOSE blades give scratch-free POLISHED cuts on wood, RIP or CROSSCUT, up to 2-inches thick. They have a 30-degree Alternate Top Bevel with a 5-degree Face Hook on 10-inch diameters and smaller.
This Diablo saw blade is designed to meet the needs of the construction and remodeling market. This advanced laser cut blade features a thin kerf, making it ideal for portable and low powered saws on the jobsite. A permanent Perma-SHIELD coating keeps this blade free from gumming and corrosion, and laser-cut stabilizer vents reduce vibration and heat buildup for more precise cuts and longer cutting life. This blade offers the quality that fine cabinetmakers expect from Freud, yet this blade is designed for the rough world of professional construction. This blade leaves a smooth, velvety finish that requires little to no sanding. Ideal for crosscutting oak, pine, melamine, veneer plywood, and delicate mouldingForrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. The Solid-Surface Planer carbide-tipped saw blade is especially designed for: Avonite, Corian, Fountainhead, and other solid surface material where the "ultimate" smooth cut is desired. Specially engineered clearances on the carbide teeth totally eliminate chipping and side scoring. The Result... perfect joints that last for years. 50% to 300% Longer Life Between Sharpening - Reduced Yearly Sharpening Costs - Less Machine Downtime - Improved Labor Efficiency - Inventory Savings - Fewer Blades Required.
LU81M series blades from Freud are the perfect blades for fast sizing of thick or stacked chipboard up to 3-1/2 inches high and also work well for hard and soft woods and plywood where surface finish is less important than cut speed. The micrograin carbidForrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Recommended for: thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods. Eliminates need for a small scoring saw blade on table saw work. The 40° points slice through thin bottom layers with no tears or chips. Reduced yearly sharpening costs - less machine downtime.
LU81M series blades from Freud are the perfect blades for fast sizing of thick or stacked chipboard up to 3-1/2 inches high and also work well for hard and soft woods and plywood where surface finish is less important than cut speed. The micrograin carbid